ZDTC64
Production Long-hole Drilling Rig
ZDTC64 is a remote-controlled underground production rig for small to medium drifts. It supports upward, downward and sidewall drilling with a hydraulic positioning unit, PLC control and anti-jamming functions.
Built around your working task.
Review the model and technical reference together with your application requirements. Provide hole diameter, depth, orientation and the working profile. Identify the available power, water and access conditions for the proposed equipment.
Inquire about ZDTC64Technical specifications
Confirm engine power and drilling coverage against the selected configuration. Published drilling rates are not guaranteed production rates.
| Hole diameter | 45–64 mm |
|---|---|
| Drilling depth | Up to 20 m |
| Impact power | 24 kW |
| Maximum drilling force | 23 kN |
| Remote control distance | 50 m |
| Roll-over angle | 360° |
| Drill rod length | 915–1525 mm |
| Main motor | 55 kW |
| Total installed power | 68 kW |
| Ground clearance | 260 mm |
| Outer / inner turning radius | 4400 / 2500 mm |
Check the operating conditions.
Provide hole diameter, depth, orientation and the working profile. Identify the available power, water and access conditions for the proposed equipment.
Check the current technical sheet against the configuration in the quotation. Dimensions, interfaces and operating requirements should be confirmed before planning the installation.
Production drilling in small to medium drifts
ZDTC64 is a remote-controlled underground production rig with a documented 45–64 mm hole-diameter range and drilling depth up to 20 m. The source describes upward, downward and sidewall work with hydraulic positioning and anti-jamming control.
Start with the drilling pattern rather than depth alone. Include hole orientations, spacing and the available setup area. These details allow the required positioning task to be compared with the machine's confirmed feed and carrier arrangement.
Documented construction and equipment
The positioning unit combines feed tilt and rotation with a pendulum arm and slide table. The control description includes anti-jamming and rapid forward and return movement of the rock drill, with remote control for setup, positioning and drilling.
The specified rod length is 915–1525 mm. The drilling-unit table identifies a manual rod retainer for one feed, a stated drilling depth up to 20 m and maximum drilling force of 23 kN; the parallel-positioning slide table is hydraulic.
Hydraulic positioning and drilling equipment
The reference lists a 360° roll-over angle, drill rods from 915 to 1525 mm and a maximum drilling force of 23 kN. Rod length, drilling force and completed-hole depth are different specification items. Ask which rod and feed arrangement is included for your planned holes.
The drilling system has a stated 24 kW impact-power reference, while the listed main motor is 55 kW and total installed power is 68 kW. Keep these figures separate when discussing the site electrical supply. Request the full utility and connection requirements for the quoted configuration.
Compare the required duty with other production rigs
ZDTC89 and ZDTC89-2 provide other production-drilling arrangements in the catalogue. Automatic rod-handling features described for those models should not be transferred to ZDTC64 without documentation. State any rod-handling requirement explicitly in the inquiry.
Include the route, available ground clearance and planned control position. The source lists a 50 m remote-control-distance reference, but operating position and site procedures still need review. A guaranteed drilling rate is not published because the available material does not establish performance for your rock conditions.
Selection questions
What should I include in a product inquiry?
Provide hole diameter, depth, orientation and the working profile. Identify the available power, water and access conditions for the proposed equipment.
Which technical details need confirmation?
Confirm engine power and drilling coverage against the selected configuration. Published drilling rates are not guaranteed production rates.
How do I request the selected configuration?
Send the model or series reference and your project requirements through the inquiry link. Include drawings or the existing equipment reference where available.
Is automatic rod handling included on ZDTC64?
Do not assume it from other rigs in the range. The reviewed ZDTC64 material supports remote control and hydraulic positioning; request the exact rod-handling scope for the offered configuration.